Physical Fitness Stack Exchange is a question and answer site for physical fitness professionals, athletes, trainers, and those providing health-related needs. Join them; it only takes a minute:

Sign up
Here's how it works:
  1. Anybody can ask a question
  2. Anybody can answer
  3. The best answers are voted up and rise to the top

My max deadlift is 350 (still gaining), but I can deadlift 300 twice. Is it better to focus on my 2 lift max or my single lift max to build overall strength?

share|improve this question

Practical Programming's Answer: 1-3RM For Strength

From page 79:

Strength, a basic objective of training and an important component of power performance, is gained using lower repetitions (1 to 3) with heavier weights (90 to 100% of 1RM).

Notice that in this context, Rippetoe is using a narrow definition of strength that does not include power, hypertrophy or endurance. Doing fewer reps and only one or two sets makes for a drastically lower volume and average load at the limit of your ability (I'm paraphrasing from the second paragraph on page 82 there). For these reasons (and the increased danger of injury), I would recommend against using 1RM or 2RM as regular training stimulus.

Though the original on page 60 of PP is better (the gradations from range to range are less stark) this chart from reddit does an excellent job explaining the effects of different rep schemes: enter image description here

Rippetoe's Reasoning For 5RM Instead of 1-3RM

The key line for you is from page 102, emphasis mine:

Absolute strength is gained by using very low reps (1-3) per set, mass is increased with higher reps (10 to 12), and local muscular and systemic endurance is developed with even higher reps (20+). For the novice, a repetition scheme that is right in the anaerobic middle works best: sets of 5 reps. Fives are close enough to the strength end of the continuum to provide tremendous increases in strength, the primary goal of the novice. Fives are also enough reps to develop a tolerance for elevated work levels, and provide for a good amount of hypertrophy so that muscular weight gain occurs too.


Fives are optimal for the novice; they effectively stimulate strength gains and other forms of progress without producing sufficient muscular or neuromuscular exhaustion to cause technique deterioration at the end of the set.

It's very possible that you still fall within the novice range of your potential. If that's the case, deadlifting sets of 5 instead of 1 or 2 would be optimal for overall development. If you've found that you cannot progress with daily increases, or that the 5RM is too taxing despite eating and resting sufficiently, working with sets of 2 or 3 in the deadlift could be better.

share|improve this answer
How much difference does rep cadence (i.e. time under load) make? – intuited Jan 25 '12 at 8:50
There is a fuzzy line between taking breaths during a 5-rep set and doing 5 singles. They've been talking about that difference on Rip's forum recently (it's down right now, so no link). Being forced to do 5 singles tells me that I'm not training or recovering sufficiently to do a good set of 5, so I should probably repeat that weight next time. – Dave Liepmann Jan 25 '12 at 14:51
I'm talking more about the speed at which the reps are done — how fast you move your muscles when they are moving. Some say that moving them slowly is much more useful, and that the theory of rep counts is based on doing reps much more slowly than most people do. 6 seconds per rep seems to be the ideal. – intuited Jan 25 '12 at 18:41
"Time under load" may be a valuable method. I'm not familiar with it, though I've heard of it in bodybuilding. Your comment would do well as its own answer (or question). – Dave Liepmann Jan 25 '12 at 18:53


I would stick with novice programming on this lift for now. A 5/3/1 might work, but I think it would be more efficient just to focus on making linear progression work.


If your max deadlift is 350, it doesn't make a lot of sense to worry about your 1 rep max (1RM) or 2RM. At that stage it's more productive to focus on your 4RM or 5RM. You want to focus on building your strength and power with heavy sets of 4-6 reps, not demonstrating it in a max single. This is also much less likely to cause injury, and easier to recovery from.

A 300 pound 2RM deadlift is still well within the range of linear progression. Weekly or twice-weekly sets of 5, adding 2.5 or 5 pounds each session or every other session, should be feasible if you're getting enough rest and eating enough.


I'll be double-checking pages 79-82 in Practical Programming later to make sure this makes sense (per Starting Strength forums).

share|improve this answer

I don't think there's a big difference between doing 2x and 1x. Both are focusing on the extreme of strength. I personally prefer to do 1x just because the higher weight (compared to 2) boosts my ego, and removes any ambiguity when I want to calculate set weights based on my 1 rep max.

That said, you'll probably do better to apply stimulus in something more like the 4 rep range, and just use 1 or 2 rep sets to test your progress. For example, my current weekly (well, I use an 8 day week to get 2 days of rest between each cycle) workout (based on the Texas workout described in Practical Programming) is this:

  • Monday: 6 sets of 4 at 80% 1RM
  • Wednesday: Lighter supplemental exercises, no deadlift.
  • Thursday: 3 sets of 4 at 65% 1RM
  • Saturday: 1RM at 100% (try for a personal record every week)

In a schedule like this, you can alternate 1RM or 2RM on the last day. A reccommendion in practical programming was to alternate 1 and 2 every other week.

share|improve this answer

Your Answer


By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.